http://windandsunpower.com/store/ Wind And Sun Power - Appropriate Alternative Energies en 1440 Thu, 26 Jan 2012 00:06:02 -0700 Zen-Cart v.1.5.7 RSS 2.0 Feed Copyright (c) 2012 Jeff Mason sales@windandsunpower.com (Jeff Mason) http://windandsunpower.com/store/ http://windandsunpower.com/store/favicon.ico http://windandsunpower.com/store/index.php?main_page=product_info&products_id=65&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=65 DUMP CONTROLLERS - EVOLVED UNIVERSAL RELAY DIVERSION CHARGE CONTROLLER MODEL 1URDC-V5 (finale) 12V (Board Version 5.1.X) For both EMRs (ElectroMechanical Relays) and SSRs (Solid State Relays) For Wind, Solar and Hydro Now with 3-Stage When Using SSR's in Diversion/Dump Mode! (See manual for use with different voltage LA Batteries) DESCRIPTION The Universal Relay Diversion Controller/Regulator is a low cost Microprocessor controlled Diversion/Dump type controller designed for the DIY (Do It Yourselfer). It is designed to switch up to 6 conventional automotive style electromechanical relays (EMR) directly with up to 800ma total coil current draw with up to 240A power handling capability. Also unlike other controllers of this type of design, it will also control DC-DC Solid State Relays (SSR) in Legacy/Conventional (Dump) diversion mode or use a 2-Stage or Intelligent/Smart 3-Stage charge algorithm including a manual Equalization mode. It is theoretically able to directly switch up to 32 SSR's at 25ma each (untested). If using just 40 amp SSR's that adds up to a potential 1280A (2560A using 80 amp SSR's) power handling capability. To keep cost down, this controller was designed for the DIY (Do It Yourselfer) and is the BOARD ONLY and does not include an enclosure. It can be mounted directly on a wall in a area protected from the environment or in a Optional or user supplied enclosure. To keep cost down and prevent unnecessary waste this manual is available in PDF format only (just printout what you need). The latest version of this manual is Free for DOWNLOAD HERE 1URDC_V5_1_Manual.pdf from WindAndSunPower.com FEATURES The ability to Directly Switch up to 6 Electromechanical or 32+ DC-DC Solid State Relays Legacy Dump/Diversion/On-Off - Electromechanical or Solid State Relays 2-Stage - Dump/Diversion (using 20ms on - 20ms off or faster SSR's Only ) 3-Stage - Dump/Diversion (using 10ms on - 10ms off or faster SSR's Only ) Manual Equalization Mode (using 20ms on - 20ms off or faster SSR's Only) Extremely Low Power Consumption (≤ 10ma) in Standby/Monitoring Accurate Battery Voltage Tracking Switching Speeds Up To 50 On-Off Cycles Per Second When Using SSR's (≤50Hz) User Settable Dump/Diversion/On-Off/Absorb Voltage Set-point (13.1 to 15.1 Volts) User Settable Float Voltage Set-point (12.5 to 14.5 Volts 3-Stage using SSR's Only) User Settable Equalization Voltage Set-point (14.5 to 16.5 Volts using SSR's Only) Optional FLA Temperature Compensation -40°F(-40°C) to 140°F(60°C) .0168V per 1°F Optional SLA Temperature Compensation -15°F(-26°C) to 140°F(60°C) .012V per 1°F The Ability to Divert/Dump 800ma Directly for Very Small Systems Self Resetting Fuses (Separate Power and Microcontroller Section Fuses) Multicolored LED Status Indicator LED Relay Power/Active Indicator Test Button Voltage Limiter (limits Maximum voltages to Approx 14.8V Except Equalization mode) Reverse Polarity Protection Over Voltage Protection Over Current Protection Transient/Lightning/Surge Protection SPECIFICATIONS Min. Operating Volts 7 VDC Max. Operating Volts 30 VDC Nominal Operation Voltage 12VDC FLA Temperature Compensation (W/Optional Probe) -40°F(-40°C)140°F(60°C) .0168V per 1°F ± 5% (Flooded Lead Acid) SLA Temperature Compensation (W/Optional Probe) -15°F(-26°C)140°F(60°C) .012V per 1°F ± 5% (GEL/SLA) Dump/Absorption Adjustment Range 13.5 to 15.5 Volts Float Voltage Adjustment Range 12.5 to 14.5 Volts Equalization Voltage Adjustment Range 14.5 to 16.5 Volts Battery Voltage Regulation (High/Low Volts Using EMRs) ± 6% ± 0.93V (This specification can fluctuate due to system variables and design) Battery Voltage Regulation (High/Low Volts Using SSRs) ± .5% + 0.03V (This specification can fluctuate due to system variables and design) Status LED Accuracy ± .5% + 0.03V Voltage Limiter 14.8V ± 0.1V Standby Power ≤ 10ma Power Max. ≤ 35ma Power Sunk Max. -800ma Automotive style ElectroMechanical Relays 1 up to 6 30 to 40 Amp with 12VDC coil Solid State Relays 2-Stage & Equal 3-Stage DC-DC 1 to 32? ≤20ms On/Off ≤10ms On/Off EMR Operating Frequency Dump Volt Setting -0.3V + 4 Sec. SSR Operating Freq. 2-Stage & Equal 3-Stage ≤25Hz(On+Off 25 x Sec.) ≤50Hz(On+Off 50 x Sec.) Operating Temp. Storage Temp. -20°C to 50°C -50°C to 150°C Dimensions 75 mm x 100 mm (2.95 in. x 3.93 in.) Specifications subject to change without notice. Made in USA Components-Rest of World WARRANTY: WindAndSunPower.com. Model 1URDC is warranted to be free of defects in material and workmanship for three years from the date of purchase. Failure to provide correct installation, operation or care for this product, in accordance with the instruction manual, will void the warranty. Product liability shall be limited to repair or replacement, at the discretion of the manufacturer. The manufacturer is not responsible for the labor or other charges necessitated by the removal, transportation, or re-installation of any defective product. Warranty does not cover damage due to, mishandling, abusive conditions, lightning, or exposure to weather. No specific claim of merchantability shall be assumed or implied beyond what is printed in this manual. No liability shall exist from circumstances arising from the inability to use this product, or it’s inappropriateness for any specific purpose. In all cases, it shall be the responsibility of the customer to insure a safe installation in compliance with local, state and national electrical codes. http://windandsunpower.com/store/index.php?main_page=product_info&products_id=65 Thu, 26 Jan 2012 00:06:02 -0700 59.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=2&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=2 MPPT500HV 500 Watt 12/24/48V 45A MPPT Current Boosting Solar Charge Control. (2-STAGE Bulk and Float - Maximum Power Point Tracking) (Dependent upon stock, this item could be drop-shipped from the manufacturer) Description: The model MPPT 500HV is a high performance current boosting solar control. Through the use of advanced microprocessor control and a high efficiency power converter, power wasted in older PWM style solar controls is converted into higher charge current. The MPPT 500HV allows for input voltage conversion. This increases the Maximum Power Point voltage and allows for higher boost current over wider operating conditions. A high accuracy digital volt and amp meter displays battery voltage, photovoltaic current and battery charge current. Proper battery charging is maintained over a wide temperature range with the battery temperature sensor. Battery float voltage is accurately regulated. Night time battery discharge is eliminated through the use of a high efficiency Schottky diode. Maximum input power to the MPPT 500HVÂ is 500 watts. Maximum photovoltaic input voltage is 100 VDC open circuit. The model MPPT500HV is optimized for operation at higher PV input voltages. Operation: When power is available from the solar panel, the MPPT 500HV microprocessor measures and determines the optimum operating point of the solar panel to produce the highest charge current possible to the battery. There is no interaction between the MPPT 500HV and other battery charging systems. The float voltage of the MPPT 500HV is calibrated to 14.1 volts. When the battery voltage reaches 14.1 volts the red Float LED turns on. At this point, charge current to the battery will gradually diminish to maintain the 14.1 float voltage. As soon as a load is turned on, maximum charge current is applied to the battery. Temperature compensation adjusts the float voltage to properly charge the battery over a wide temperature range. When the battery is warm the float voltage will drop and when the battery is cold the float voltage will rise. MPPT 500HV is well suited for flooded, deep cycle and gel type batteries. Features: Maximum power point tracking technology provides up to 30% more power from the solar array Built-in digital display shows battery voltage and charge current Temperature compensation Lightning protection Maximum solar open circuit voltage is 100 volts Use with a 12, 24, or 48 volt system Voltage setpoint is adjustable to accommodate different battery types Charge a low voltage battery from a high voltage solar array, reducing wire losses Internal Schottky diode prevents night time battery discharge Includes five year manufacturer's warranty Specifications: At 12V Output At 24V Output At 48V Output PV Charge Current: 45 amps continuous 22 amps continuous 11 amps continuous Surge Current: 54 amps for 10 min. 26.4 amps for 10 min. 13.2 amps for 10 min. Min. Battery Voltage: 10 volts 10 volts 10 volts Float Voltage Range: 12.5 to 15.5 volts 25 to 31 volts 50 to 60 volts Float Preset, Flooded Battery: 14.1 volts 28.2 volts 56.4 volts Float Preset, Sealed Battery: 13.8 volts 27 volts 55.2 volts Specifications that are not dependent on battery voltage: Array Voltage Open Circuit: 100 volts max. Digital Meter: ½in LCD display PV Input Voltage: Auto-ranging DC Volts Range: 0-99.9 volts ±0.5% Input Power Max.: 500 watts DC Amps Range: 0-99.9 amps ±0.75% Input Power Min.: 100 watts Temp. Comp.: -18mV/°C nominal Reverse Current: 0.01 amps nominal Min. Battery Capacity: 100 amp-hours Operating Temp.: -20 to +60°C Storage Temp.: -30 to +70°C Operating Current: 0.15 amps nominal Float Regulation: ±0.05 volts nominal Wire Size: #2 AWG max. Mounting: #6 screws Efficiency: > 95% at 35 amps Finish: Beige powder coat Weight: 3 pounds Conduit Size: 0.5 inches Lightning Protection: 1000 watt MOV Dimensions: 6in x 8.5in x 3in Specifications subject to change without notice. Full specs/Owners manual Manufactured In USA BZ Products, INC. BZ PRODUCTS, INC. Model MPPT 500 is warranted to be free of defects in material and workmanship for five years from the date of purchase. NO RETURNS! I am not authorized by BZ Products Inc. to accept returns. All warranty work, returns and tech support is handled directly by BZ Products Inc. Contact info for BZ Products can be found in your installation guide or at their website http://www.bzproducts.net/. I ship Worldwide! I claim full price on customs forms for insurance purposes. You are responsible for all tares, tariffs and taxes! Do your homework as some countries can get quite expensive! http://windandsunpower.com/store/index.php?main_page=product_info&products_id=2 Fri, 06 Jan 2012 07:04:33 -0700 234.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=3&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=3 500 Watt 12/24/48V 45A MPPT Current Boosting Solar Charge Control. (2-STAGE Bulk and Float - Maximum Power Point Tracking) (Dependent upon stock, this item could be drop-shipped from the manufacturer) Description: The model MPPT 500 is a high performance current boosting solar control. Through the use of advanced microprocessor control and a high efficiency power converter, power wasted in older PWM style solar controls is converted into higher charge current. The MPPT 500 allows for input voltage conversion. This increases the Maximum Power Point voltage and allows for higher boost current over wider operating conditions. A high accuracy digital volt and amp meter displays battery voltage, photovoltaic current and battery charge current. Proper battery charging is maintained over a wide temperature range with the battery temperature sensor. Battery float voltage is accurately regulated. Night time battery discharge is eliminated through the use of a high efficiency Schottky diode. Maximum input power to the MPPT 500 is 500 watts. Maximum photovoltaic input voltage is 100 VDC open circuit. The model MPPT500HV is optimized for operation at higher PV input voltages. Operation: When power is available from the solar panel, the MPPT 500 microprocessor measures and determines the optimum operating point of the solar panel to produce the highest charge current possible to the battery. There is no interaction between the MPPT 500 and other battery charging systems. The float voltage of the MPPT 500 is calibrated to 14.1 volts. When the battery voltage reaches 14.1 volts the red Float LED turns on. At this point, charge current to the battery will gradually diminish to maintain the 14.1 float voltage. As soon as a load is turned on, maximum charge current is applied to the battery. Temperature compensation adjusts the float voltage to properly charge the battery over a wide temperature range. When the battery is warm the float voltage will drop and when the battery is cold the float voltage will rise. MPPT 500 is well suited for flooded, deep cycle and gel type batteries. MPPT 500 Standard Features: Current boosting Voltage converting 12, 24 and 48 volt operation Up to 45 Amps charge current PWM float control Fully automatic operation Easy installation Large #2 wire connectors Five year warranty Digital volt and amp meter Up to 500 watt input Battery temperature sensor standard MPPT 500 SPECIFICATIONS: FLOAT VOLTAGE IS FACTORY SET TO 14.1 VOLTS . Output current 12 volts 45 amps continuous Surge current 120% for 10 min. Output current 24 volts 22 amps continuous Digital meter 1/2in LCD display Output current 48 volts 11 amps continuous DC volts range 0-99.9 volts ± .5% Array voltage open circuit 100 volts open circuit DC current range 0-99.9 amps ± .75% Input power max. 500 watts Input power min 100 watts Float voltage 14.1/28.2/56.4 flooded Float voltage 13.8/27/55.2 sealed Temp. comp. -18mV/° C nominal Float regulation ± .05 volts nominal Reverse current . 01 amps nominal Photovoltaic input auto ranging Min battery voltage 10 volts Battery capacity 100 AH minimum Operating temp. -20 to + 60° C Storage temp. -30 to + 70° C Float voltage range 12.5 to 15.5 volts Operating current .15 amps nominal Float voltage range 25 to 31 volts Weight 3 pounds Float voltage range 50 to 60 volts Wire size # 2 max AWG Mounting # 6 screws Lightning protection 1000 watt MOV Efficiency >95% at 35 amps Finish Beige powder coat Size 6in x8½in x2 3/8in Conduit size 1 inch Specifications subject to change without notice. Full specs/Owners manual Manufactured In USA BZ Products, INC. BZ PRODUCTS, INC. Model MPPT 500 is warranted to be free of defects in material and workmanship for five years from the date of purchase. NO RETURNS! I am not authorized by BZ Products Inc. to accept returns. All warranty work, returns and tech support is handled directly by BZ Products Inc. Contact info for BZ Products can be found in your installation guide or at their website http://www.bzproducts.net/. I ship Worldwide! I claim full price on customs forms for insurance purposes. You are responsible for all tares, tariffs and taxes! Do your homework as some countries can get quite expensive! http://windandsunpower.com/store/index.php?main_page=product_info&products_id=3 Fri, 06 Jan 2012 07:04:33 -0700 214.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=4&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=4 Twenty Five Amp MPPT Current Boosting Solar Charge Control. (2-STAGE Bulk and Float - Maximum Power Point Tracking) This is a Panel/Flush Mount (For surface mount you need the optional enclosure or to make your own) (Dependent upon stock, this item could be drop-shipped from the manufacturer) The model MPPT250HV is a 25 amp high performance current boosting solar control optimized for use with the Kaneka GSA211 60 watt solar panels and other systems utilizing High Voltage arrays. Through the use of advanced microprocessor control and a high efficiency power converter, power wasted in older PWM style solar controls is converted into higher charge current. The MPPT250HV allows for input voltage conversion. This increases the Maximum Power Point voltage and allows for higher boost current over wider operating conditions. You can charge a 12 volt battery from a high voltage solar panel. A high accuracy digital volt and amp meter displays battery voltage and charge current. An auxiliary 100 ma 13.8 volt trickle charger is provided to keep the engine/generator start battery fully charged. A 15 amp capacity low voltage disconnect protects the battery from over discharge conditions. Proper battery charging is maintained over a wide temperature range with the battery temperature sensor. Battery float voltage is accurately regulated. Night time battery discharge is eliminated through the use of a high efficiency Schottky diode. Maximum normalized input power to the MPPT250HV is 250 watts Operation: When power is available from the solar panel, the MPPT250HV microprocessor measures and determines the optimum operating point of the solar panel to produce the highest charge current possible to the battery. There is no interaction between the MPPT250HV and other battery charging systems. The float voltage of the MPPT250HV is factory set to 14.1 volts. The float voltage is adjustable. When the battery voltage reaches the float voltage the red Float LED turns on. At this point, charge current to the battery will gradually diminish to maintain the float voltage. As soon a load is turned on, maximum charge current is applied to the battery. Temperature compensation adjusts the float voltage to properly charge the battery over a wide temperature range. When the battery is warm the float voltage will drop and when the battery is cold the float voltage will rise. The MPPT250HV is well suited for flooded, deep cycle and gel type batteries. A low voltage disconnect is included to protect the battery from excessive discharge by automatically turning off a load, such as lights that may have been left on. Load is disconnected when the battery voltage is 12.0 volts or lower. When the batteries are recharged to 12.6 volts the low voltage disconnect reconnects the load. The yellow LED on the face of the MPPT250HV is lit when the load is connected. Operation of the low voltage disconnect is fully automatic. Maximum low voltage disconnect load current is 15 amps. Do not connect the low voltage disconnect to inverters. MPPT 250HV Standard Features: Current boosting Digital volt and amp meter 12volt operation 25 Amp charge current PWM float control fully automatic operation Easy installation Low voltage disconnect Five year warranty Auxiliary battery charger included Flush mount Battery temperature sensor standard SPECIFICATIONS: PV Charge Current: 25 amps continuous Digital Meter: ½ in LCD display Surge Current: 35 amps for 10 min. DC Volts Range : 0-99.9 volts ±0.5% Array Voltage Open Circuit: 100 volts max. DC Amps Range : 0-99.9 amps ±0.75% Input Power Max.: 250 watts Temp. Comp.: -18mV/°C nominal Input Power Min.: 68 watts PV Input: 100 volts nominal PV Input Voltage: Auto-ranging Reverse Current: 0.01 amps nominal Min. Battery Voltage: 10 volts Min. Battery Capacity: 100 amp-hours Operating Temp.: -20 to +60°C Storage Temp.: -30 to +70°C Float Voltage Range : 12.5 to 15.5 volts Float Voltage Preset: 14.1 volts Operating Current: 0.15 amps nominal Float Regulation: ±0.05 volts nominal Wire Size: #12 AWG max. Mounting #6 screws Efficiency: > 95% at 20 amps Finish: Black powder coat Weight: 2 pounds Auxiliary Charger: 13.8 volts at 0.1 amps Lightning Protection: 1000 watt MOV Dimensions: 7.8in x 5.1in x 2.5in LVD Current: 15 amps max. LVD Current: 20 amps surge LVD Disconnect: 12.0 volts LVD Reconnect: 12.6 volts Specifications subject to change without notice. Full specs/Owners manual Manufactured In USA BZ Products, INC. BZ PRODUCTS, INC. Model MPPT 500 is warranted to be free of defects in material and workmanship for five years from the date of purchase. NO RETURNS! I am not authorized by BZ Products Inc. to accept returns. All warranty work, returns and tech support is handled directly by BZ Products Inc. Contact info for BZ Products can be found in your installation guide or at their website http://www.bzproducts.net/. I ship Worldwide! I claim full price on customs forms for insurance purposes. You are responsible for all tares, tariffs and taxes! Do your homework as some countries can get quite expensive! http://windandsunpower.com/store/index.php?main_page=product_info&products_id=4 Fri, 06 Jan 2012 07:04:33 -0700 134.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=5&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=5 Twenty Five Amp MPPT Current Boosting Solar Charge Control. (2-STAGE Bulk and Float - Maximum Power Point Tracking) This is a Panel/Flush Mount (For surface mount you need the optional enclosure or to make your own) (Dependent upon stock, this item could be drop-shipped from the manufacturer) The model MPPT250 is a 25 amp high performance current boosting solar control. Through the use of advanced microprocessor control and a high efficiency power converter, power wasted in older PWM style solar controls is converted into higher charge current. The MPPT250 allows for input voltage conversion. This increases the Maximum Power Point voltage and allows for higher boost current over wider operating conditions. You can charge a 12 volt battery from a high voltage solar panel. A high accuracy digital volt and amp meter displays battery voltage and charge current. An auxiliary 100 ma 13.8 volt trickle charger is provided to keep the engine/generator start battery fully charged. A 15 amp capacity low voltage disconnect protects the battery from over discharge conditions. Proper battery charging is maintained over a wide temperature range with the battery temperature sensor. Battery float voltage is accurately regulated. Night time battery discharge is eliminated through the use of a high efficiency Schottky diode. Maximum normalized input power to the MPPT250 is 250 watts. Operation: When power is available from the solar panel, the MPPT250 microprocessor measures and determines the optimum operating point of the solar panel to produce the highest charge current possible to the battery. There is no interaction between the MPPT250 and other battery charging systems. The float voltage of the MPPT250 is factory set to 14.1 volts. The float voltage is adjustable. When the battery voltage reaches the float voltage the red Float LED turns on. At this point, charge current to the battery will gradually diminish to maintain the float voltage. As soon a load is turned on, maximum charge current is applied to the battery. Temperature compensation adjusts the float voltage to properly charge the battery over a wide temperature range. When the battery is warm the float voltage will drop and when the battery is cold the float voltage will rise. The MPPT250 is well suited for flooded, deep cycle and gel type batteries. A low voltage disconnect is included to protect the battery from excessive discharge by automatically turning off a load, such as lights that may have been left on. Load is disconnected when the battery voltage is 12.0 volts or lower. When the batteries are recharged to 12.6 volts the low voltage disconnect reconnects the load. The yellow LED on the face of the MPPT250 is lit when the load is active. Operation of the low voltage disconnect is fully automatic. Maximum low voltage disconnect load current is 15 amps. Do not connect the low voltage disconnect to inverters. MPPT 250 Standard Features: Current boosting Digital volt and amp meter 12volt operation 25 Amp charge current PWM float control fully automatic operation Easy installation Low voltage disconnect Five year warranty Auxiliary battery charger included Flush mount Battery temperature sensor standard MPPT 250 SPECIFICATIONS: PV charge current 25 amps continuous Digital meter 1/2in LCD display Surge current 35 amps 10 min. DC volts range 0-99.9 volts ± .5% Array voltage open circuit 50 volts open circuit DC current range 0-99.9 amps ± .75% Input power max 250 watts Temp. comp. -18mV/° C nominal Input power min 68 watts PV input 12 or 24 volts nominal PV input voltage auto ranging Reverse current . 01 amps nominal Min battery voltage 10 volts Battery capacity 100 AH minimum Operating temp. -20 to + 60° C Storage temp. -30 to + 70° C Float voltage range 12.5 to 15.5 volts Weight 2 pounds Operating current .15 amps nominal Float regulation ± .05 volts nominal Wire size # 12 max AWG Mounting # 6 screws Efficiency >95% at 20 amps Finish black powder coat Float voltage 14.1 volts Aux batt charger 13.8 volts .1 amp max. Lightning protection MOV 1000 watt Size 7.8in x5.1in x2.5in LVD current 15 amps max LVD current 20 amps surge LVD disconnect 12.0 volts LVD reconnect 12.6 volts Specifications subject to change without notice. Full specs/Owners manual Manufactured In USA BZ Products, INC. BZ PRODUCTS, INC. Model MPPT 500 is warranted to be free of defects in material and workmanship for five years from the date of purchase. NO RETURNS! I am not authorized by BZ Products Inc. to accept returns. All warranty work, returns and tech support is handled directly by BZ Products Inc. Contact info for BZ Products can be found in your installation guide or at their website http://www.bzproducts.net/. I ship Worldwide! I claim full price on customs forms for insurance purposes. You are responsible for all tares, tariffs and taxes! Do your homework as some countries can get quite expensive! http://windandsunpower.com/store/index.php?main_page=product_info&products_id=5 Fri, 06 Jan 2012 07:04:33 -0700 129.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=50&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=50 NEW OPTIONAL BZ MPPT250 MPPT259HV SURFACE MOUNT ENCLOSURE BOX! 8.0 in X 5.1 in x 2.0 in Manufactured In USA by: BZ Products, INC. (Dependent upon stock, this item could be drop-shipped from the manufacturer) http://windandsunpower.com/store/index.php?main_page=product_info&products_id=50 Fri, 06 Jan 2012 06:42:43 -0700 29.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=64&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=64 1 SSR Plus 1 40A Rated Heat Sink 40 ADC 5-220 VDC Load Voltage 3-32 VDC Control Voltage DC-DC SSR Solid State Relay Pre-Assembled with a SSR Thermal Pad Item Description: I Have been using these SSR's on my system and to design and test the 1URDC for about 2 years now with ZERO Problems. These are the same SSR's that can be found on eBay. (DC Loads & DC Control Only! Do Not Use This With AC!) Brand: mager Model: MGR-1 DD220D40 Load Current: 40A DC Max Rated Load Voltage: 5-220VDC Actual (24-220VDC Marked) Control Voltage: 3-32VDC Control Current: 5-25mA On Voltage: ≤2.3VDC Off Leakage Current: ≤2mA On-off Time: ≤10mS Dielectric Strength: 2000VAC Insulation Resistance : 500M ohm/500VDC Ambient Temperature.: -30℃ to 75℃ Working indicators: LED Certification: CE Made in China http://windandsunpower.com/store/index.php?main_page=product_info&products_id=64 Fri, 09 Dec 2011 04:49:28 -0700 49.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=53&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=53 Optional 8 foot long Temperature Probe for 1URDC Boards V4.3.x and up. If you have Board V4.2.8 with the buzzer Please contact me for shipping details for FREE Temperature Compensation hardware and software upgrade to use the new model Probe. This includes upgrading the probe if you have previously purchased one. (Black tip only, the new model has a Red and Black tip.) This upgrade eliminates the Alarm feature and increases the Temperature Compensation range from 130F to -5F to a new range of 140F to -40F. http://windandsunpower.com/store/index.php?main_page=product_info&products_id=53 Tue, 23 Aug 2011 14:15:10 -0700 15.00 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=62&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=62 1URDC-V4 OPTIONAL ENCLOSURE WALL MOUNTING BRACKET KIT BUD INDUSTRIES NBX-10920 Design Features Used to mount enclosures to walls, panels , or any other flat surface. *Corrosion resistant stainless steel construction *Kit comes complete with four brackets and bracket/enclosure mounting screws http://windandsunpower.com/store/index.php?main_page=product_info&products_id=62 Tue, 23 Aug 2011 14:13:42 -0700 6.95 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=60&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=60 1URDC-V4 OPTIONAL ENCLOSURE CABLE GLAND BUD INDUSTRIES NG-9512 Cable Range - .16"-.31" Mounting Hole - .61" (5/8" drill) Design Features Required to maintain NEMA 4X rating when cables enter or exit a NEMA 1, 2, 4, 4x, 12 or 13 type enclosure. Assembly consisting of black molded nylon body, hex nut, and cable nut and with a rubber gasket and cable seal. Nylon material has UL94V-2 flammability rating and -40C to 100C suggested service temperature. http://windandsunpower.com/store/index.php?main_page=product_info&products_id=60 Tue, 23 Aug 2011 14:13:13 -0700 2.95 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=59&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=59 OPTIONAL NEMA INDOOR CLEAR DOOR ENCLOSURE FOR 1URDC-V4 NO HOLES DRILLED! YOU MUST DRILL YOUR OWN MOUNTING THROUGH THE BACK AND WIRE ENTRY HOLES! SS MOUNTING BRACKETS ARE ALSO AVALABLE FOR THESE IF YOU DO NOT WANT TO DRILL MOUNTING HOLES. BUD INDUSTRIES NBF-32202 These gasketed all-plastic enclosures have been designed meet NEMA 1, 2, 4, 4x, 12, 13 and IEC529-IP66 requirements, which allows them to be used in many wet, dirty and/or corrosive environments. Design Features Designed to IP66 of IEC 529 and NEMA 1, 2, 4, 4x, 12, and 13 specifications All plastic construction including hinge pins Has two plastic latches Indoor Version: ABS plastic enclosures are molded out of light gray material with UL94-HB flammability rating. (Not UL Listed) ABS/PC blended plastic enclosures are molded out of light gray material with UL94-5VA flammability rating. Suggested service temperature range -40C to +70C. Clear doors, for all models, are molded out of polycarbonate material with UL94-V0 flammability rating http://windandsunpower.com/store/index.php?main_page=product_info&products_id=59 Tue, 23 Aug 2011 14:11:44 -0700 21.95 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=58&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=58 American Terminal SPDT ER-1200 Electromechanical Automotive Relay Brand new premium heavy duty Bosch style SPDT relays 5 pronged Metal mounting tab that can be removed 12 Volt 30/40 amp relays Contact : N.O 40 Amp. / 14 VDC Contact : N.C 30 Amp. / 14 VDC Coil : 160ma at 14V 1" x 1-1/8" x 2" Terminal .250" http://windandsunpower.com/store/index.php?main_page=product_info&products_id=58 Fri, 21 Jan 2011 05:58:38 -0700 2.95 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=10&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=10 High performance, low voltage drop 5 Amp 60 Volt Schottky Blocking Diode http://windandsunpower.com/store/index.php?main_page=product_info&products_id=10 Wed, 17 Nov 2010 15:54:02 -0700 1.98 USD http://windandsunpower.com/store/index.php?main_page=product_info&products_id=9&language=en http://windandsunpower.com/store/index.php?main_page=product_reviews&products_id=9 High performace, low voltage drop 3 Amp 60 Volt Schottky Blocking Diode http://windandsunpower.com/store/index.php?main_page=product_info&products_id=9 Sun, 14 Nov 2010 10:36:25 -0700 1.49 USD